Returning Customers: Log In

Products - Handbells: Handbell Care and Maintenance


Introduction

Welcome to the growing Schulmerich family! We put a lot of ourselves into our handbells, and it delights us to know that you will soon be using them to make beautiful music, enjoy good fellowship and have great fun.


Your new handbells are 100% American made, warranted for life, and the finest handbells available anywhere. Schulmerich’s Lifetime Warranty covers the entire bell, from the tuned bell casting and the clapper assembly to the handle. We will give you the service and support you need, for as long as you own your Schulmerich handbells. No wonder Schulmerich bells are played by more churches, schools and institutions than any other. We are the oldest existing manufacturer of English handbells in North America, having started in 1962. We are proud that you have chosen to play them, too.

---- Team Schulmerich

To help you learn more about the care and maintenance of your Handbells, we have put together the following download-able Schulmerich Handbells Care and Maintenance guide [PDF]


CARRYING CASES

Your cases are beautifully designed to transport or store your bells. They also provide additional storage space for maintenance
tools and materials furnished with your bells. Although your bells are received in plastic bags, please do
not use these bags for continued storage as this may harm the highly polished finish on the bells. To maintain this
jewel-like finish on the outside of the bells, it is important to avoid contact with rough or coarse materials, or touching
them with the bare hand. If you do not own Schulmerich custom-designed carrying cases, we recommend that storage
bags or pouches of soft materials, such as pacific cloth, flannels, or velvets be made for your bells. We also recommend
that your cases be aired (in a dry environment) once a year.

INSPECTION UPON RECEIPT

Please take a few minutes to check your new bells for shipping damage. It is the responsibility of the recipient to file a damage claim if such is necessary. A tool kit and a specially treated polishing cloth in a plastic container are also included, with complete sets of bells. We suggest you review this instruction bulletin, and note pages of helpful illustrations. A parts diagram is included for your ordering convenience, should the need arise.

GETTING TO KNOW YOUR BELLS

As you examine your bells, set a large one aside (a G4 provides good visibility of the internal parts and construction), so you can become familiar with some of its unique parts and features.

The Soft Touch™ plastic handle of polypropylene copolymer features inlaid enharmonic musical note designations and a campaniform (bell silhouette). The campaniform shows the strike point side of the handbell, and is also used for rapid identification for those who use uneven spring tension adjustment. Two locating pin holes in the block, to which the handle is securely riveted, indicate the relationship of the handle to the striking plane of the clapper.

The striking plane of the clapper (selected at the factory as the point of “best response” which, when used as the strike point, creates the clearest tone) is fixed by an indexing pin in the casting to a hole located in the clapper yoke. As each bell is individually tuned, the optimum striking plane is permanently recorded by scribing an index mark along the inner surface of the bell casting. It is most important that no attempt be made to buff out this mark. Such attempts may result in detuning the bell. Schulmerich bells provide an indexing pin (a Schulmerich exclusive) and inlaid enharmonic note designations with campaniform marking and Soft Touch durable handle.

Note the raised crown, or bell “tang,” at the top of the bell. This Schulmerich exclusive helps produce greater amplitude.

Next examine the plastic handguard (Master Touch™ Guardian Disc) and notice that it carries the same plasticcoated note designation as does the handle. This permits identification of the bell, whether the playing preference is to lay the bells on their sides or to stand them upright on their mouths, or by reading from the handle or handle disc respectively. This musical note system is in direct reference to that of the piano keyboard (Example: Middle C is C5.) Now look into the mouth of the bell and notice the unique Select-A-Strike™ clapper that allows you nearly unlimited freedom for voicing your bells. (Or, you may have selected the Quick-Adjust™, which can be easily hand adjusted for Soft, Medium or Hard voice settings.)

Schulmerich manufactures two types of adjustable clappers — Select-A-Strike™ and Quick-Adjust™, shown below. Select-A-Strike™ clappers are adjustable by securing the clapper head against the casting wall, then rotating the clapper screw slightly counter-clockwise until the clapper is free to rotate. Rotate the clapper to the desired position and secure the clapper head against the casting wall while retightening the screw. Quick-Adjust™ clappers are adjustable without loosening the clapper screw.


On all bells C8 and below in pitch, three decidedly different impact tones (timbres) can be achieved. This permits a selection of mellow or brilliant tones to be generated in your bells, according to your tonal preference. These options provide a soft mellow strike tone designated by the letter “S” imprinted on the clapper insert, a medium tone designated by “M” on the insert, and a strong brilliant tone designated by “H” on the insert. Try it!

It is far better to have bells which musically have the same timbre than to have bells which are set on similar clapper settings to achieve a special effect.

Try our clapper and listen for these differences in timbre. First, with the felt material (G#4 and lower bells) striking the bell (the “S” plane of the clapper in the striking plane), strike the bell softly and then with a hard strike – while noting the low, mellow tones which result. Next, loosen the screw which holds the clapper, using the screwdriver furnished for this purpose – or just rotate it, if you have Quick- Adjust™ clappers – and turn the clapper so that the “M” plane of the clapper is oriented to strike. Adjust the clapper so that the center of the slot or hole in the “M” plane will contact with the side of the bell. Then tighten the clapper securely and again strike the bell softly and then with a hard strike, and note the medium, mellow tones which result. Now, loosen the clapper again, align the “H” plane to strike, tighten the screw, and again strike the bell and note the hard, brilliant tones which will result.

Bells higher in pitch than G#4 are equipped with clappers whose design does not include a felt striking position. As we progress higher than G#4, it is necessary to use harder impact materials to excite the higher tonal frequencies. Therefore, in ascending order, the clappers contain smaller slots or holes, or none at all in bells C#8 and above, in order to generate these higher frequencies. This is opposed to that of the larger bells where the purpose of the felt is to subdue the extraneous higher partials and thereby achieve a dominant strong fundamental and twelfth partial. Even in smaller bells, small changes in strike tone can be achieved by striking on the thicker or thinner areas of the clapper head since the thicker areas, being more resilient, provide a softer striking surface.

Now, look further down into the bell and examine the unique Micro-Adjust control at the bottom of the clapper shaft (below). Note the two elastic stop nuts (a type of highfriction nut that holds the position to which it is turned) which restrict the movement of the Pellethane Restraining Spring secured to the bottom of the clapper.


Note: Adjusting the stop nut downward forces the Pellethane Restraining Spring down, thereby moving the clapper further from the opposite side of the bell. Downward or upward adjustment of either or both nuts offers minute control of the clapper position.
Hold the clapper lightly to one side of the bell and, using the appropriate nut driver furnished (bells G2-F#3 use 3/8", bells G3-B5 use 5/16", and bells C6-C8 use 1/4" nut drivers), turn the nut counter-clockwise and you will notice that the clapper moves closer to the side of the bell, thus requiring less effort to strike the bell. Now release the clapper and turn the nut clockwise (downward) and you will see the clapper move away from the side of the bell. The purpose of adjustment is to permit the selection of the desired clapper restraining action to suit the touch or feel of any bell ringer. Uneven adjustment of the nuts can be utilized to give an easier forward strike, or restrict the backstroke to avoid unwanted backrings.

Obviously, excessive downward adjustment of the nuts will require excessive effort to strike the bell since the clapper is held too far from the side of the bell. Excessive downward positioning of the nuts can overstress the Pellethane Restraining Spring to a point where spring failure could occur. Position nuts downward only as far as necessary to effect a smooth, easy and controlled strike. To achieve uniform tension settings throughout the handbell set, it is generally better to adjust for what is best for the bells, instead of what is preferred by individual ringers. Whatever method you use, make certain that each bell can pass the following tests:
  • Check for a full dynamic range
  • Check back ringing
  • Check the “shake” technique (not applicable to bass bells), performed by striking the clapper head against both front and back casting walls
  • Check that the clapper head strikes only once when playing a Martellato (table technique)
CARING FOR YOUR BELLS

The following suggestions will help you get a lifetime of satisfaction from your Schulmerich bells:

Never put your bells away after playing or handling them without first having wiped them clean with the specially treated polishing cloth furnished as part of your accessory kit. Make this a rule and a habit. If left on, finger and hand marks, due to body salts and acids, will quickly etch and mar the bright, polished finish. The bell should be dry before using the polishing cloth. If the bell is badly tarnished, a slight moistening of the tarnished surface by blowing on it will help. Rub the surface briskly with the outside of the polishing cloth, and then with the brown cloth, using the hands against the outside cloth to protect them from jeweler’s rouge. Coloring on the hands is harmless and is easily washed off.

Should a bell become so badly tarnished that it cannot be cleaned with the polishing cloth, cleaning with a polish such as Simichrome®, available from Schulmerich, will remove most stubborn tarnish. When using polish, apply with a clean soft cloth or cheesecloth. Do not allow the polish to dry. Remove immediately following application.

DISASSEMBLY

If disassembly of a bell is necessary or desired for some reason, the hex ball driver furnished is the only tool needed. A look at the diagram on the opposite page shows that the entire bell assembly is held together by means of one cap screw through the handle block, through the top of the bell, and then into a threaded hole in the yoke. Disassembly is performed by inserting the ball driver into the socket of the cap screw above the handle block and turning the screw counter-clockwise until its threads are free of the threaded hole in the yoke.

REASSEMBLY

To reassemble (see diagram below), replace the parts in the order illustrated in the diagram. Insert the cap screw with the washer beneath its head, through the center hole in the handle block. Place the yoke spacer bushing over the extension of the cap screw and, holding the yoke assembly by its shaft, turn the assembly clockwise, thereby drawing the screw extension into the threaded hole in the yoke. With these parts engaged, align the hole in the yoke with the extension of the indexing pin beyond the inside of the bell. Push the parts together, so that the yoke and handle are indexed by the pin and complete the tightening of the cap screw until it is drawn snug. Note: Over-tightening of the cap screw may (especially in the higher range of bells) result in a deadening of the bell tone – so draw the screw up snug, but not so tight as to deaden the tone or to bind the yoke assembly.

Should the plastic handle become gummy from dirt accumulation after a time, clean with a cloth moistened with a lukewarm solution of water and mild detergent. The plastic material is unaffected by almost all strong chemicals and cleaning agents except benzene and carbon tetrachloride. which will affect the plastic only after long contact with it – avoid their use.


In addition to the type of plastic used in the handle, your Schulmerich bell may use as many as four additional types. Different types of plastics are more or less susceptible to reaction with different types of chemicals and to different degrees. Many of today’s better products include plastic parts and assemblies for the added advantages that plastics offer, and most reliable manufacturers caution against the use of various chemicals on their plastics. Schulmerich therefore recommends against the use of any chemicals either on its bell assemblies or in the storage container with the bells. In a closed container such as a carrying case, under certain conditions, a stored chemical can give off a gas that could react injuriously with one or more the plastics. For example, the fumes given off by ordinary mothballs can have damaging effects on plastic. So, play it safe, and don’t put chemicals into your bell storage cases and follow the Schulmerich instructions for cleaning.

No special care is needed for the ruggedly built Schulmerich bell carrying cases. The plush-lined, profiled recesses for the bells in each of the available cases provide excellent resistance against abrasion and wear. The tough, black leatherette covering bonded to the exteriors of the cases will stand considerable abuse. Scuff marks on the finish, resulting from rough handling, can be simply touchedup with an application of one of several black self-shining liquid shoe polishes on the market.

VOICING YOUR HANDBELLS

Definition of Terms:
VOICING: The process of blending the tonal qualities (sound) of the bells together to bring about a consistent color or timbre.
VOICE BREAK: All octaves of handbells contain a variety of clapper sizes and density. The voice break is located where the clapper size, weight, and/or design changes, producing a timbre change.

Understanding Basic Patterns of Handbell Sound:

   •
As pitch rises, clappers get smaller and harder.
   • As identical clappers proceed up the scale, the sound tends to become softer.
   • Bells below the voice break tend to be darker/weaker in color and those above tend to be brighter/stronger. (There are some exceptions)

Voicing Procedures:
All handbell mechanisms (yoke assemblies)/clapper assemblies, must have proper tension settings.

Voicing your Handbells:
  1. Set all clapper heads at "Medium."
  2. Beginning at the lowest musical pitch, work your way to the right, playing at least 4 -5 chromatic bells up the scale and then back down and past the handbell being voiced.
  3. Listen for weak or strong handbells.
  4. Rotate the clapper heads accordingly. (NOT ALL BELLS WILL BE SET AT THE SAME SETTING.)
  5. For a more consistent sound and feel, use the same hand in voicing your bells.
Rotation of Clapper Head:
Select-A-Strike™ clappers use the entire 360° of the clapper head. Even a slight adjustment to the left or right of a particular setting will make a difference.

For bells with Quick-Adjust™ clappers, rotate the clapper head as desired.

Voicing Options:

You can exchange clappers of the same size and numeric designation and use them in different bells. (Experimental process in Select-A-Strike™ only.)

Different clapper materials used throughout the years have caused a variety of tonal colors. Some have become softer, while others have become hard. Newly designed and better blending clappers are available through Schulmerich.

REPAIRING YOUR BELLS

There need be no reluctance in disassembling your handbells. They have been designed so that you, the customer, can do repair work that will have no effect on the precision tuning of the bells.

SPRING REPLACEMENT

(For bells with Select-A-Strike™ clappers)

Tools Required:
Handbell toolkit provided with original set of bells

1. Using the hex ball driver supplied, remove the cap screw located at the handle block. This completely disassembles the bell. Be careful not to lose any of the parts, particularly the spacer bushing that goes between the yoke assembly and the casting. Failure to reinsert this bushing could result in a tonally “dead” bell.

2. Using the screwdriver, remove the clapper and washer and set aside.

3. Using the adjustment wrenches supplied, remove stop nuts, neoprene bumpers and anti-friction washers. (Rotate rather than pull.)

4. Remove the damaged spring by sliding toward the clapper end of the shaft (note springs fit snugly).

5. Inspect the clapper end of the shaft. If there are any sharp edges or burrs, remove them with a small file.

6. Place the Pellethane Restraining Spring with flat center portion on a board or other hard surface, and push down on the ends of the spring to open up the center hole. Insert the end of the hex shaft through the center hole, reverse the yoke and continue to push the spring down fully to straddle the block and be parallel with the sides of the “U” channel so that the studs are free from the sides of the slots.

Pellethane Restraining Springs are numbered for easy replacement:

#7 G2 thru F#3
#1 G3 thru C#4
#3 D4 thru G#4
#4 A4 thru B5
#5 C6 thru C7
#6 C#7 thru C8

7. Replace the anti-friction washer, neoprene bumper and stop nut on each stud. Hand tighten now – and then adjust when the bell is together.

8. Bell reassembly: Please refer to Reassembly in previous section.

SPRING REPLACEMENT

(For bells with Quick-Adjust™ clappers)

Tools Required:
Handbell toolkit provided with original set of bells Standard 5/32" short arm hex wrench

1. Using the 5/32" hex ball driver, remove the shoulder screw retaining the clapper assembly. Note: Do not use the hex ball driver to remove or tighten this screw, as permanent damage to the screw head could result. Remove clapperhead, fiber washer, bushing, and detent spring from the clapper shaft.

2. Using the nut driver from the handbell toolkit, remove the adjusting stop nuts, neoprene bumpers, and antifriction washers from the studs.

3. Remove old spring and install new one.

4. Reinstall the anti-friction washers, neoprene bumpers, and adjusting stop nuts on the studs.

5. Reinstall the detent spring on the clapper shaft. Align tangs with flats on shaft. Place the fiber washer, bushing, and clapper head on the shoulder screw and reinstall on the clapper shaft.

6. Hand-tighten shoulder screw with 5/32 hex driver.

7. Set clapper to desired position and readjust spring for proper function. It is recommended that the clapper be rotated in a clockwise direction when changing settings. Note: This procedure can be followed to replace any of the Quick-Adjust™ clapper head assembly parts.

STICKING CLAPPER SHAFTS

If you encounter sticking clapper shafts on bells G3 - C8, we recommend using the new Yoke Adjustment Tool available from Schulmerich Bells. It’s easy to use, provides the best long term results, and is less likely to damage bell parts. The Yoke Adjustment Tool is designed to spread the inner walls of the yoke assembly outward, in order to free up any binding which might occur. Disassemble the handbell before attempting the following procedure.


Gently insert the open ends of the Yoke Adjustment Tool into both ends of the yoke assembly and gently squeeze (see diagram); this applies outward pressure to the inside walls of the yoke assembly. It should not require a great deal of force. If the clapper shaft does not free itself up after two attempts, you might need professional assistance. Again, disassemble the bell before attempting this procedure.

If a Yoke Adjustment Tool is not available, you may address the problem by a less preferred method. Take a thin-bladed long shaft screwdriver and place it between the shaft block and the yoke channel and apply a moderate twisting motion. If the shaft does not free itself, do not apply more force. It is recommended to follow this procedure on both sides of the yoke assembly. Take care not to cause damage to any parts. It is not necessary to disassemble the bell for this procedure. This method may not provide long term results and should be viewed as a “temporary fix.”

LOOSE CLAPPER SHAFTS

Loose or wobbly shafts can be detected by a rattling sound heard when the bell is struck. If you can hear a rattle and feel excessive side to side movement, you can take the following steps to correct it. (Remember that there must be some side movement to permit the bell to strike.)

Remove the yoke assembly from the bell by loosening the cap screw. Place the yoke block on its side over an open vise and gently compress vise. This will tighten the channel. Now reassemble the bell and you are ready to ring.

REPLACING MASTER TOUCH™ GUARDIAN DISCS

Tools Required:
Handbell toolkit provided with original set of bells; Small hammer

Bell Disassembly:
1. Insert hex key wrench into head of screw located in center of handle. Turn counterclockwise until screw is disengaged from bell.

2. Remove washer and place washer on screw furnished with kit.

3. Set aside yoke, spacer, and handle.

4. With a small hammer, drive indexing pin flush with top of bell tang.

5. Place new indexing pin from kit above (atop) old pin. Drive new pin in as existing pin is driven out. Stop when old pin drops out.

Bell Assembly:
1. Place new disc over bell tang.
2. Drive indexing pin further into bell until it is 1/8" above top of disc.
3. Orient bell with scribed line (inside bell lip) nearest you. Orient disc with “SCHULMERICH” to your left.
4. Put yoke, spacer, and handle assembly in place.
5. Insert new screw with washer and tighten using hex key wrench or ball driver. Note: Overtightening screw may deaden bell tone.
6. General Notes: Use caution so as not to scratch or damage the new disc. Some older bells used an internal tooth washer over the tang, not needed with new discs.

BUZZING TONE

This sometimes occurs in the larger bells. After determining that the bell is not cracked, ring the bell and hold the handguard firmly with your thumb. In most cases you will note the buzz is gone. If this is not the case, simply retighten the cap screw. If, after tightening the screw, the noise still persists when you remove your thumb from the handguard, loosen the handle to the point where the handguard easily spins. Move handguard slightly to one side and retighten the screw. This should correct the problem.

QUIETING A SQUEAKING YOKE ASSEMBLY

You may lubricate each end of the axle with a single drop of WD-40® or Super Lube® with Syncolon® (PTFE) in tube applicator 51010. Allow penetration for several minutes and then wipe off any access. Do not use any other method of lubrication. Do not mix lubrication products. (Super Lube is available from Schulmerich.)

CLAPPER & YOKE ASSEMBLY

(6th & 7th octaves, high range only)


1. Remove a bumper from supplied sheet with tweezers and place in recess in slot on yoke. Push edges to seat.

2. Install two spring plungers into clapper with screw head toward the clapper head and only the white plungers extending out the bottom of the rocker end.

3. Slide clapper assembly into yoke. Slide pin into side hole of yoke and line up clapper with pin. Drive pin in with press until flush with side of yoke.

4. Check clapper for swing action.

TIGHTENING LOOSE HANDLES

(7th octave, low range only)


1. Remove the eight (8) handle screws on the sides of the handle with the 3/32" T-handle hex wrench.

2. Tighten the main cap screw with the 1/4" T-handle hex wrench until snug and without a visible gap between the base of the handle and the handguard.

3. Replace the handle screws securely. Note: Check the handle screws periodically for tightness.

ADJUSTING 6th & 7th OCTAVE HIGH BELLS

When adjusting the clapper assembly, note that the screw on the strike side controls the strike while the screw on the backswing side controls the backswing. Make small adjustments to each with a screwdriver until the bell rings properly.

POLISHING THE BELLS

Polishing is necessary especially after exposure to a corrosive atmosphere such as salt air, etc., or having something spilled on the bells.

Always make sure to polish under the handguard, but be careful to wipe away all polish residue. On the smaller bells this will require disassembly. If this is not done, the bells will continue to tarnish. If let go, the tarnish will actually etch the bronze. If anything is spilled on the bells, clean it off immediately, as bronze is easily etched.

We recommend the use of Simichrome® Metal Polish, which can be purchased directly from Schulmerich.

Occasionally clean the inside of your bells with a clean, dry cloth.

We hope the above will aid you and help you further enjoy your Schulmerich handbells. If you have any further questions please feel free to contact us at any time; we will be glad to help you.

INFORMATION OF INTEREST

Caution should be exercised when transporting handbells in extremely cold weather. Allow sufficient time for all parts to reach room temperature before the bells are struck.

HANDBELL PART ORDERING INFORMATION

To purchase replacement parts, please refer to the Handbell Parts List.

TROUBLE SHOOTING COMMON PROBLEMS

Buzzing
Check Guardian Disc................................ Loosen handle and rotate disc (old style only)
  * Master Touch™ Disc will require complete removal of the handle
Check anti-friction washers....................... Replace
Check condition of "bronze" springs........... Replace with Pellethane springs
Check casting for cracks.......................... Consult local handbell representative or Schulmerich
Check handle and cap screw.................... Tighten cap screw (do not overtighten)
Check clapper head screw........................ Tighten clapper screw

Dull Tone Or Too Little Sound:
Check handle cap screw............................ Cap screw is too tight; loosen screw
Check for missing spacer........................... Disassemble bell and insert spacer in proper location
Check clapper head................................... Rotate clapper head or replace

Pitch Changes:
Check for cracked casting......................... Send to Schulmerich or contact representative
Check room temperature........................... Allow bells to reach room temperature before playing
  * Store bells in more constant environment
Note: Cold days will cause pitch to rise, hot days will cause pitch to lower.Temperature variation also affects human hearing!

Yoke Assembly Problems:
Inconsistent ringing .................................. Check tension adjustments
Back ringing............................................. Check tension adjustments
Uneven handbell shakes............................ Check tension adjustments
Slow moving clapper assembly.................. Spread yoke channel
  * Check yoke stud and axle spring alignment
  * Check and clean axle
  * See local representative

Broken Springs:
Broken springs......................................... Replace spring with Pellethane springs

Loose Or Rotating Handles Or Clapper Assemblies:
Check for broken or missing index pins..... Replace
Check handle lock-washer....................... Replace


CARE AND MAINTENANCE GUIDELINES

Daily/Weekly
Wipe off handbell castings after use by polishing with polishing cloth.

   • Minor marks can be wiped off with outside chamois section.
   • If tarnish/fingerprints are worse, use the rouge section of the outside chamois section.
   • Be sure to wipe off the red rouge from the castings and bell parts.

Do not rouge inside the castings. Report/Note any mechanical or audible changes to your Handbell Director.
Dry wipe inside the castings with a lint-free cloth.
Store handbells in a constant room temperature if possible.

Monthly
Snug/Tighten handbell handle screw with hex ball driver.(Do not overtighten!)
Snug/Tighten clapper head screws on Select-A-Strike™ Standard assemblies.
Adjust spring tension, especially if temperature changes have occurred.
Spot polish excessive tarnish or marks on casting exteriors.
Inspect all parts and mechanism alignments.

Bi-Annually
Polish castings with SIMICHROME polish if needed.
Listen to the voicing of the clapper heads.
Check spring tension adjustments.
Clean yoke assembly parts with a brush.
Inspect all parts.

Yearly
Open cases, remove handbells, and air out cases for 40-48 hours.
Inspect cases for damage, and repair as needed.
Use Armor-All® or similar product on outside of cases. Touch up scuff marks with black shoe polish.
Repair damaged locks and latches.
Vacuum all cases.
Clean handles and discs in mild solution of water and soap with damp cloth.

Please note: Fingerprints and hand marks, if left on, will quickly etch the casting surface due to body salts and acids.

This schedule is provided as a guideline. The activities undertaken may be adjusted depending on your use of the bells and the playing environment.

INFORMATION OF INTEREST
Caution should be exercised when transporting handbells in extremely cold weather. Sufficient time to permit all parts to reach room temperature should be allowed before the bells are struck.

FACTORY REFURBISHMENT AND REPAIR

Schulmerich Handbells can be readily maintained by the user. However, nobody knows your bells like the people who made them. For those who want to schedule a factory refurbishment and repair, for complete octaves or individual bells, we offer two options.
  1. Complete refurbishment, including replacement of all parts (except bell casting).
  2. Polishing and cleaning, including replacement of parts (except bell casting) where necessary.
Each of these services includes handbell disassembly, cleaning and polishing of the bell castings, reassembly, tuning check, ringing check, visual check and placing the refurbished handbells in plastic bags. Where cases will not be replaced, we will vacuum the inside and use a spray cleaner on the outside.

You may contact us directly at our Sellersville Headquarters, where all factory refurbishing work will be scheduled. For an appointment, you may use our toll free telephone number: 800/772-3557.

We assure you that the refurbishment will be done at the highest possible quality level and in a timely fashion.

THE SCHULMERICH WARRANTY

Schulmerich handbell instruments purchased after May 15, 1984 are warranted to be free from defects in material and workmanship, covering all parts, for the life of the ownership of such instruments by the original purchaser. Defective parts will be repaired or replaced, at Schulmerich’s option, provided such parts are returned shipping prepaid to Schulmerich Bells, Carillon Hill, P. O. Box 903, Sellersville, PA 18960-0903. Proof of purchase (Schulmerich’s invoice) may be required.

This warranty is extended solely to the original purchaser, and is non-transferable.

This warranty is VOID in the event of abuse, accident, modification to parts, or improper handling, or repairs or alterations made by the owner or third parties without Schulmerich factory written authorization. Parts will be considered abused if they have been treated contrary to Schulmerich’s Care and Maintenance Instructions. Further, this warranty does not cover any damage arising from nicks, dents or scratches.

This warranty gives you specific legal rights and you may have other rights which may vary from state to state.

With the exception of warranty of title, ALL OTHER WARRANTIES ARE EXPRESSLY DISCLAIMED, THUS THERE IS NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

No one is authorized to change these terms.

Schulmerich Carillons, Inc. • Carillon Hill
P.O. Box 903 • Sellersville, PA 18960-0903
800/772-3557 • 215/257-2771
www.SchulmerichBells.com

Pellethane is a trademark of Dow Chemical Company.
WD-40® is a registered trademark of WD-40 Company.
Super Lube® is a registered trademark of Synco Chemical Corp.
ArmorAll® is a registered trademark of The ArmorAll/STP Products Company.

Subscribe/Unsubscribe to our information Email list!

You will be asked to confirm subscribe/unsubscribe requests via email.
Email Address
 
Home | About Us | Products | Services | Community | Contact | Terms of use | Site Map | Newsletter | RISR Login
2008 © Schulmerich Carillons, Inc - All Rights Reserved
Web Design and Software Development By Klotnet Software